Specifications: SE80AX620SCRNG — Airtac SE double-acting, single-rod pneumatic cylinder; 80 mm bore, 620 mm stroke, sus420j2 stainless steel piston rod, with magnet, NBR seal option and G3/8 ports. Mounting configuration: rear pivot support used with cb.
Product Catalog
Download Airtac Product Catalog (PDF)
For detailed product dimensions and mounting drawings, please download and refer to the PDF catalog.
Model Code Explained
| Code |
Meaning |
| SE |
SE series, double-acting single-rod cylinder |
| 80 |
80 mm bore |
| A |
SUS420J2 stainless steel piston rod |
| X |
Separator before stroke |
| 620 |
620 mm stroke |
| S |
With magnet in the piston |
| CR |
Rear pivot support used with CB |
| N |
NBR (nitrile rubber); basic seal references are not the N bill of materials |
| G |
G3/8 port thread |
Technical Specifications
| Parameter |
Value |
| Model |
SE80AX620SCRNG |
| Action |
Double acting, single rod |
| Bore |
80 mm |
| Stroke |
620 mm; Non-standard configurable stroke; confirm order and delivery conditions |
| Piston rod |
SUS420J2 stainless steel |
| Magnetic piston |
With magnet; a sensor is not implied included |
| Mounting selection |
Rear pivot support used with CB |
| Seal option |
NBR (nitrile rubber); confirm individual seal materials |
| Port thread |
G3/8 |
| Working medium |
Clean compressed air filtered through a 40 µm or finer filter |
| Operating pressure |
0.15–1.0 MPa (1.5–10 bar; approximately 22–145 psi) |
| Proof pressure |
1.5 MPa (15 bar); not the continuous operating pressure |
| Operating temperature |
−20 to 70 °C; avoid freezing condensate |
| Piston speed |
30–800 mm/s; select controls for the actual load and piping |
| Stroke tolerance |
+1.5 / 0 mm |
| Cushioning |
Adjustable pneumatic cushioning at both ends |
| Series cushion-stroke reference |
36 mm nominal catalog value; actual deceleration depends on stroke, load and adjustment |
| Rod diameter and end thread |
25 mm; M20 × 1.5 |
| Sensor selection |
Optional CMSE or DMSE sensor for this magnetic configuration; select the exact sensor separately |
| Calculated weight reference |
8827.2 g (8.8272 kg); bare-cylinder reference, excluding mounting and rod-end accessories |
Weight basis: 2484.6 g non-stroke mass + 620 mm × 10.23 g/mm. Basic-catalog reference estimate; N-seal and rod-material mass corrections unlisted. Not measured or packed shipping weight. Mount masses are unlisted and excluded. Actual supplied mass prevails.
Features and Operation
- The catalog lists ISO 15552 and VDMA 24562 as the cylinder design standards; this is not a separate certification claim.
- Compressed air alternately drives the piston in both directions. The profiled double-acting piston seal has a compact, oil-retaining design.
- Square aluminum-alloy barrel without external tie rods, with adjustable end cushioning. Use external guidance where the load would bend or twist the rod.
- Select mounting parts to match the motion and load path. A catalog-compatible accessory is not automatically included in the delivery.
External and Mounting Dimensions
Basic SE80 geometry is identical with or without a magnet. Dimensions are in mm except threads. Derived overall lengths include the rear locating boss but exclude mounts, rod-end joints, air fittings, sensors and packaging.
| Parameter |
Value |
| A + stroke, retracted |
834 mm = 214 + 620; rod-thread end to rear-cover face, excluding rear locating boss |
| AC + stroke, body face span |
748 mm = 128 + 620 |
| Bare-cylinder overall length, retracted |
838 mm = 214 + 620 + 4 |
| Bare-cylinder overall length, fully extended |
1458 mm = 214 + 2 × 620 + 4 |
| Body cross-section, width × height |
93 × 93 mm (□B) |
| Mounting holes |
8 × M10 (K), 19 mm deep (KA); 72 × 72 mm centers (□KB) |
| Rod diameter / rod-end thread |
D = 25 mm; E = M20 × 1.5; EA = 40 mm |
| Locating bosses |
ØM = 45 mm; ØN = 45 mm; rear projection NA = 4 mm |
| Rod-end local dimensions |
AB = 86; DA = 53; F = 26; FA = 10; H = 22 mm |
| Cover and port local dimensions |
AD = 33; AE = 33; MA = 33; PA = 16.5; PB = 8 mm; P = G3/8 |
Mount symbols refer to their own drawings; unrelated dimensions cannot be added into a verified assembly length × width × height.
| Parameter |
Value |
| Selected accessory |
CB: Rear double clevis; part F-SE80CB |
| Material |
Ductile cast iron |
| A+stroke |
834 mm = 214 + 620 |
| C+stroke |
748 mm = 128 + 620 |
| Dimensions (mm) |
CC = 36; CD = 15.5; CE = 16; CJ = 22 |
| Dimensions (mm) |
CP = 50; CT = 90; PA1 = 97; PB1 = 90.5 |
| Dimensions (mm) |
S = 93; T = 72 |
| Selected accessory |
CR: Rear pivot support used with CB; part F-SI80CR |
| Material |
Ductile cast iron |
| A+stroke |
834 mm = 214 + 620 |
| C+stroke |
748 mm = 128 + 620 |
| Dimensions (mm) |
AA = 63; B = 50; CC = 16; CD = 92.5 |
| Dimensions (mm) |
CJ = 19.5; D = 47; E = 40; F = 59 |
| Dimensions (mm) |
G = 14; H = 66; I = 85; K = 11 |
| Dimensions (mm) |
L = 17 |
CP shown with ±0.1mm tolerance; CE is hole diameter. PA1/PB1 refer to the drawn pin, not a separate verified order code. CR requires CB. K is through-hole diameter, L counterbore diameter, four fixing holes.
For detailed product dimensions and mounting drawings, please download and refer to the PDF catalog.
Assembly and Accessory Selection
CR requires the matching CB clevis; it must not be installed alone. Confirm the ordered combination and supplied hardware.
| Optional part |
Application and reference |
| F-SI80LB |
Foot mount (LB); low-carbon steel |
| F-SI80FA |
Front flange (FA); aluminum alloy |
| F-SI80FA |
Rear flange (FB); aluminum alloy |
| F-SE80CA |
Rear single clevis (CA); ductile cast iron |
| F-SE80CB |
Rear double clevis (CB); ductile cast iron |
| F-SI80CR |
Rear pivot support used with CB (CR); ductile cast iron |
| F-SE80TC |
Trunnion mounting bracket (TC) |
| F-SI80FTC |
Front trunnion mount (FTC); cast steel |
| F-SI63TCM1 |
Trunnion support type 1 (TCM1); cast steel |
| F-SI63TCM2 |
Trunnion support type 2 (TCM2); aluminum alloy |
| F-M20X150I |
I-type rod-end joint; 608 g catalog reference. Drawing dimensions: NC = 20; ND = 80; NE = 102; NF = 40; NG = 30; NH = M20×1.5; NM = 20. |
| F-M20X150Y |
Y-type rod-end joint; 860 g catalog reference. Drawing dimensions: NA = 44.4; NC = 20; ND = 80; NP = 40; NQ = 101; NM = 20; NH = M20×1.5; PA = 53.4; PB = 45.2. |
| F-M20X150F |
Floating joint; 865 g catalog reference. Drawing dimensions: MA = 102; MB = 29; MC = 13; MD = 46; ME = 53; MF = 22; MG = 10; MH = 22; MI/MJ = M20×1.5; MK = 10°. |
| F-M20X150U |
Spherical rod-end joint; 370 g catalog reference. Drawing dimensions: PA = 18; PB = 46; PC = 20; PD = 33; PE = 77; PF = 100; PG = M20×1.5; PH = 15°; PI = 34; PJ = 30; PK = 25. |
All four rod-end alternatives use M20 × 1.5; match the exact pitch. Drawing dimensions are in mm except threads and angles. CR requires CB; FTC and TC pair with TCM1 or TCM2. Joint drawings define added assembly space; add their masses only when supplied. Floating-joint MK is angular compensation; the M6-and-under radial-offset note does not apply.
CMSE/DMSE require the S piston. Hardware, sensors, joints and service parts are separate unless ordered. Match SE80 seal kits, wear rings, guide bushings and covers to the actual seal and production revision; replacement magnets apply only to magnetic models. Confirm service-part codes; bore and drawing callouts alone are insufficient.Compatible Magnetic Sensors
This S configuration has a magnetic piston and accepts E-profile DMSE or CMSE switches in its sensor groove. The options below are ordered separately; select the output and cable for the controller, supply and installation. S does not include a sensor or connection cable.
| Sensor option |
Electrical selection and complete order codes |
| DMSE: 2-wire electronic |
10–28 V DC; load 2.5–100 mA, max. 2.8 W. Direct cable: DMSE-020, DMSE-030, DMSE-050, DMSE-100. Quick connector: DMSE-M08, DMSE-M08010, DMSE-M08020, DMSE-M08030, DMSE-M12, DMSE-M12010, DMSE-M12020, DMSE-M12030. IP68 direct cable: DMSE-020-W, DMSE-030-W, DMSE-050-W, DMSE-100-W. |
| DMSE: NPN 3-wire |
5–30 V DC; max. 200 mA and 6 W; sinking output. Direct cable: DMSE-N020, DMSE-N030, DMSE-N050, DMSE-N100. Quick connector: DMSE-NM08, DMSE-NM08010, DMSE-NM08020, DMSE-NM08030, DMSE-NM12, DMSE-NM12010, DMSE-NM12020, DMSE-NM12030. IP68 direct cable: DMSE-N020-W, DMSE-N030-W, DMSE-N050-W, DMSE-N100-W. |
| DMSE: PNP 3-wire |
5–30 V DC; max. 200 mA and 6 W; sourcing output. Direct cable: DMSE-P020, DMSE-P030, DMSE-P050, DMSE-P100. Quick connector: DMSE-PM08, DMSE-PM08010, DMSE-PM08020, DMSE-PM08030, DMSE-PM12, DMSE-PM12010, DMSE-PM12020, DMSE-PM12030. IP68 direct cable: DMSE-P020-W, DMSE-P030-W, DMSE-P050-W, DMSE-P100-W. |
| CMSE: 2-wire reed contact |
5–240 V AC/DC; meet both 100 mA and 10 W maximum limits. CMSE-020, CMSE-030, CMSE-050, CMSE-100, CMSE-M08, CMSE-M08010, CMSE-M08020, CMSE-M08030, CMSE-M12, CMSE-M12010, CMSE-M12020, CMSE-M12030. |
| CMSE-H: high-temperature reed contact |
5–240 V AC/DC; meet both 100 mA and 10 W maximum limits. No indicator light. Sensor rating −10 to 125 °C; this does not raise the cylinder or complete assembly temperature limit. CMSE-020-H, CMSE-030-H, CMSE-050-H, CMSE-100-H, CMSE-M08-H, CMSE-M08010-H, CMSE-M08020-H, CMSE-M08030-H, CMSE-M12-H, CMSE-M12010-H, CMSE-M12020-H, CMSE-M12030-H. |
| A05-DMSE: flex-resistant cable |
2-wire electronic; 10–28 V DC; load 2.5–100 mA, max. 2.8 W; IP64. Direct cable: A05-DMSE-020, A05-DMSE-030, A05-DMSE-050, A05-DMSE-100. |
| A06-DMSE: oil-resistant flex cable |
2-wire electronic; 10–28 V DC; load 2.5–100 mA, max. 2.8 W; built-in IP68. Direct cable: A06-DMSE-020, A06-DMSE-030, A06-DMSE-050, A06-DMSE-100. |
| A05-CMSE: flex-resistant cable |
2-wire reed contact; 5–240 V AC/DC; meet both 100 mA and 10 W maximum limits; IP64. Direct cable: A05-CMSE-020, A05-CMSE-030, A05-CMSE-050, A05-CMSE-100. |
| M8 female cable: 2-wire CMSE / DMSE |
F-ECM08B020, F-ECM08B030, F-ECM08B050, F-ECM08B100. Lengths: 2, 3, 5 and 10 m, respectively. |
| M8 female cable: 3-wire NPN / PNP DMSE |
F-ECM08C020, F-ECM08C030, F-ECM08C050, F-ECM08C100. Lengths: 2, 3, 5 and 10 m, respectively. |
| M12 female cable: 2-wire CMSE / DMSE |
F-ECM12B020, F-ECM12B030, F-ECM12B050, F-ECM12B100. Lengths: 2, 3, 5 and 10 m, respectively. |
| M12 female cable: 3-wire NPN / PNP DMSE |
F-ECM12C020, F-ECM12C030, F-ECM12C050, F-ECM12C100. Lengths: 2, 3, 5 and 10 m, respectively. |
Cable codes: 020 = 2 m, 030 = 3 m, 050 = 5 m and 100 = 10 m. M08/M12 = M8/M12 male connector with 0.5 m lead; M08010/M12010 = 1 m, M08020/M12020 = 2 m and M08030/M12030 = 3 m. Match the separately ordered female cable to connector size, wire count and pin assignment; connector size alone is insufficient.
Standard DMSE/CMSE and A05/A06 sensors operate at −10 to 70 °C. Use the overlap of cylinder, sensor and cable ratings. General sensors are IP64; only the listed DMSE-W direct leads and A06-DMSE have IP68. A05/A06 use direct leads only; use at least a 19 mm cable bend radius and suitable protection for the environment.
For 3-wire DC sensors: brown = positive, blue = negative, black = output. NPN uses a load between positive and output; PNP uses a load between output and negative. Two-wire switches require a series load. Check residual voltage and leakage against the controller input: DMSE 2-wire max. 3.5 V / 0.06 mA; DMSE 3-wire max. 0.7 V / 0.01 mA. Connect the load before energizing and follow the selected sensor wiring diagram.
Installation: loosen the sensor screw, slide the E-profile sensor into the cylinder groove, position it within the switching range, then tighten to 0.15–0.20 N·m; never exceed 0.25 N·m. Keep wiring clear of motion and high-voltage cables. Check sensing position and secure wiring after installation.
The female cables above are optional for matching quick connectors; direct-lead sensors do not require them. Three-wire female cable pins: 1 brown (+), 3 blue (−), 4 black (output). Two-wire: pin 1 brown (+), 4 blue (−); pin 3 unused.
Force and System Selection
| Parameter |
Value |
| Theoretical extension force |
2513.0 N at 0.5 MPa; effective piston area 5026 mm² |
| Theoretical retraction force |
2268.0 N at 0.5 MPa; effective annular area 4536 mm² |
| Force calculation |
Force (N) = effective piston area (mm²) × pressure (MPa), before friction and dynamic losses; not a safe payload rating |
| Catalog load-ratio guidance |
Up to 0.7 for static/low-speed duty, 0.5 at 50–500 mm/s and 0.3 above 500 mm/s; assess actual duty |
| Required effective flow area |
At 300 / 400 / 500 / 600 / 700 / 800 mm/s: 7.9 / 10.5 / 13.1 / 15.7 / 18.3 / 20.9 mm²; this is pneumatic flow area, not piston force area |
| Tubing reference, OD × ID |
300 mm/s: 10 × 6.5 mm; 400 mm/s: 10 × 6.5 mm; 500 mm/s: 16 × 11 mm; 600 mm/s: 16 × 11 mm; 700 mm/s: 16 × 11 mm; 800 mm/s: 16 × 11 mm |
Reference speeds are not guaranteed: motion depends on load, pressure, valve flow, pipe length, fittings, cushioning and exhaust backpressure. The 0.1 MPa force reference is below the SE minimum. Long strokes need support and stability checks; heavy/fast loads may need a deceleration circuit or external absorber.
Separately ordered circuit examples, not a speed or stock guarantee. 300–800 mm/s reference: 5V31010B050,5V32010B050,4V31010BG,4V32010BG,4A31010G,4A32010G. B is 24 V DC; 5V suffix 050 specifies 0.5 m terminal leads, and the listed 4V uses DIN/internal pilot. 4A is air controlled, without a coil; 10/20 mean single/double control. 5V remains PT: match its PT fittings separately from the G cylinder/4V/4A fittings. Valve port sizes: 300-10: supply/work 3/8, exhaust 1/4. Do not infer exhaust size from the cylinder port. Valve limits are 0.15–0.8 MPa and −20–70 °C with 40 µm or finer filtered air; obey all lower circuit limits. 4A needs separate air-pilot plumbing: the PT drawings show 1/8 pilot ports, one for single and two for double control; confirm the pilot thread for a G valve.
Complete NAMUR examples based on the table families: 4M31010BG,4M32010BG. Use the corresponding speed band above. These DIN/24 V DC, internally piloted 4M valves have NAMUR A/B faces, not threaded cylinder outlets. A separately verified adapter arrangement is required; they do not mount directly to SE. No matching adapter order code is established here.
Additional flame-resistant blue 100 m tube-coil example: UN54D100065100MBU (10 × 6.5 mm, minimum bend radius 20 mm). It is rated 1 MPa at 23 °C and −20–70 °C. Apply temperature derating and confirm actual tube/fitting compatibility. Flame-resistant tubing does not certify the machine. The reviewed PA6/PA12 tables have no matching 8 × 5 or 10 × 6.5 mm row; other IDs do not inherit these sizing references. The 16 × 11 mm reference tube is US98A160110100MBU: blue 100 m US98A coil, 1 MPa working pressure at 23 °C, −20–70 °C and 80 mm minimum bend radius. Its 3 MPa burst value is not an operating rating. Apply temperature derating. A matching 16 mm connector/control chain is not established by the listed fittings, whose sockets stop at 12 mm; do not substitute 16 × 12 tube or claim the reference speed without a verified complete flow path.
Internal Components
| Catalog item |
Material / scope |
| 1 — Rod-end nut |
Carbon steel or stainless steel, according to the supplied part specification |
| 2 — Piston rod |
SUS420J2 stainless steel |
| 3 — Front-cover O-ring |
TPU (basic reference) |
| 4 — Front cover |
Aluminum alloy |
| 5 — Bushing |
Wear-resistant material |
| 6 — Cushion O-ring |
TPU (basic reference) |
| 7 — Cylinder barrel |
Aluminum alloy |
| 8 — O-ring |
NBR (basic reference) |
| 9 — Piston |
Aluminum alloy |
| 10 — Piston O-ring |
NBR (basic reference) |
| 11 — Wear ring |
Wear-resistant material |
| 12 — Magnet |
Plastic magnet for this 80 mm magnetic cylinder |
| 13 — Hexagon socket screw |
Carbon steel |
| 14 — Cushion seal |
TPU (basic reference) |
| 15 — Rear cover |
Aluminum alloy |
| 16 — Pillar nut |
Carbon steel or stainless steel, according to the supplied part specification |
Series Ordering Options
The following are series options, not additional features of this model. SE is single rod; SED is double rod; SEJ is double rod with adjustable stroke. Their dimensions and weight formulas differ. Rod material: omitted = medium carbon steel, A = SUS420J2, B = SUS304, C = SUS316. Seal option: omitted = TPU, H = fluororubber, N = NBR. S selects the magnetic piston; omitted selects no magnet. Port thread: omitted = PT, G = G thread. A different seal code alone does not establish a higher operating-temperature rating.
SE80 catalog standard strokes are 25, 50, 75, 80, 100, 125, 150, 160, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000 mm. The catalog lists a 1500 mm maximum and 1800 mm allowable stroke. Confirm non-standard orders and availability; check long-stroke rod support, load direction and stability.
Installation and Maintenance
- Installation and servicing should be performed by trained personnel. Isolate power and air and release residual pressure before servicing; prevent sudden rod movement during restart.
- Protect against dust, splash, corrosive media and freezing condensate; use suitable components for special environments. Keep magnetic versions away from strong external magnetic fields.
- Provide guarding and suitable measures against unintended movement or dropped loads after pressure loss. The cylinder alone is not a safety holding device.
- Factory prelubrication generally permits operation without added oil. If lubrication is used, use additive-free ISO VG32 turbine oil and continue lubrication once started; do not use engine or spindle oil.
- Use clean, properly treated compressed air and flush piping before connection. Keep thread sealant or tape clear of the first one to two threads to prevent contamination.
- Adjust air cushioning for the actual load and speed; avoid side loading and protect the rod surface. Cap ports and protect against corrosion during extended storage.
- Install speed controls at both cylinder ports. For commissioning, start with the flow controls closed and open them gradually from low speed; exhaust throttling is commonly used for stable speed.
- Adjust the cushion needle for the load and speed so the piston does not strike the end cover or rebound; do not force the cushion adjustment screw.
- Keep the rod axis aligned with the load motion. Guide external loads separately to avoid bending, side load and torque on the rod; support long-stroke installations against sag and vibration.
- Use a pivoting cylinder mount for swinging linkages instead of forcing a foot-mounted cylinder to follow an arc. Select front/rear flange orientation for the predominant load direction.
- Inspect seals, mount fixings, air leaks and rod condition periodically. Use service parts matched to the exact cylinder, seal material and revision; internal drawing numbers are not independent order codes.
Connection and Tube-Side Options
| Selection |
Complete codes; tube sizes as labelled |
| GBKC compression fitting |
6 × 4 mm OD × ID: GBKC0604-03; 8 × 5 mm OD × ID: GBKC0805-03; 8 × 5.5 or 6 mm OD × ID: GBKC0806-03; 10 × 6.5 mm OD × ID: GBKC1065-03; 10 × 7.5 or 8 mm OD × ID: GBKC1075-03; 12 × 8 mm OD × ID: GBKC1208-03; 12 × 9 or 10 mm OD × ID: GBKC1209-03 |
| GBB male–male adapter |
male G1/8: GBB0103; male G1/4: GBB0203; male G3/8: GBB0303; male G1/2: GBB0304 |
| GBD male–female adapter |
female G1/8: GBD0103; female G1/4: GBD0203 |
| GBZ auxiliary plug — unused auxiliary port only |
GBZ03 |
| GPC straight |
6 mm OD: GPC603,GPC603D; 8 mm OD: GPC803,GPC803D; 10 mm OD: GPC1003,GPC1003D; 12 mm OD: GPC1203,GPC1203D |
| GPL elbow |
6 mm OD: GPL603,GPL603D; 8 mm OD: GPL803,GPL803D; 10 mm OD: GPL1003,GPL1003D; 12 mm OD: GPL1203,GPL1203D |
| GPLL extended elbow |
6 mm OD: GPLL603,GPLL603D; 8 mm OD: GPLL803,GPLL803D; 10 mm OD: GPLL1003,GPLL1003D; 12 mm OD: GPLL1203,GPLL1203D |
| GPEB branch tee |
6 mm OD: GPEB603,GPEB603D; 8 mm OD: GPEB803,GPEB803D; 10 mm OD: GPEB1003,GPEB1003D; 12 mm OD: GPEB1203,GPEB1203D |
| GPED run tee |
6 mm OD: GPED603,GPED603D; 8 mm OD: GPED803,GPED803D; 10 mm OD: GPED1003,GPED1003D; 12 mm OD: GPED1203,GPED1203D |
| GPYB Y fitting |
6 mm OD: GPYB603,GPYB603D; 8 mm OD: GPYB803,GPYB803D; 10 mm OD: GPYB1003,GPYB1003D; 12 mm OD: GPYB1203,GPYB1203D |
| GPH banjo elbow |
6 mm OD: GPH603,GPH603D; 8 mm OD: GPH803,GPH803D; 10 mm OD: GPH1003,GPH1003D; 12 mm OD: GPH1203,GPH1203D |
| GPHF female-branch banjo |
6 mm OD: GPHF603,GPHF603D; 8 mm OD: GPHF803,GPHF803D; 10 mm OD: GPHF1003,GPHF1003D; 12 mm OD: GPHF1203,GPHF1203D |
| GPHW twin banjo |
6 mm OD: GPHW603,GPHW603D; 8 mm OD: GPHW803,GPHW803D; 10 mm OD: GPHW1003,GPHW1003D; 12 mm OD: GPHW1203,GPHW1203D |
| GPZB cross fitting |
6 mm OD: GPZB603,GPZB603D; 8 mm OD: GPZB803,GPZB803D; 10 mm OD: GPZB1003,GPZB1003D; 12 mm OD: GPZB1203,GPZB1203D |
| GPKD reducing distribution fitting |
main 10 / branch 8 mm OD: GPKD10-803,GPKD10-803D |
| GBPC metal straight |
6 mm OD: GBPC603; 8 mm OD: GBPC803; 10 mm OD: GBPC1003; 12 mm OD: GBPC1203 |
| GBSL exhaust silencer — valve exhaust only |
GBSL03 |
| GBSLM miniature exhaust silencer — valve exhaust only |
GBSLM03 |
| GBESL throttling exhaust silencer — valve exhaust only |
GBESL03 |
| GPSS universal flow control |
10 mm OD: GPSS1003A,GPSS1003AD,GPSS1003B,GPSS1003BD; 12 mm OD: GPSS1203A,GPSS1203AD,GPSS1203B,GPSS1203BD |
| GPTL push-lock flow control |
6 mm OD: GPTL603A,GPTL603AD,GPTL603B,GPTL603BD; 8 mm OD: GPTL803A,GPTL803AD,GPTL803B,GPTL803BD; 10 mm OD: GPTL1003A,GPTL1003AD,GPTL1003B,GPTL1003BD; 12 mm OD: GPTL1203A,GPTL1203AD,GPTL1203B,GPTL1203BD |
| PSA inline flow control |
6 mm OD: PSA6,PSA6D,PSA6-S,PSA6D-S; 8 mm OD: PSA8,PSA8D,PSA8-S,PSA8D-S; 10 mm OD: PSA10,PSA10D,PSA10-S,PSA10D-S; 12 mm OD: PSA12,PSA12D,PSA12-S,PSA12D-S |
| GPSA inline flow control |
6 mm OD: GPSA6,GPSA6D; 8 mm OD: GPSA8,GPSA8D; 10 mm OD: GPSA10,GPSA10D; 12 mm OD: GPSA12,GPSA12D |
| PPA plug-in exhaust silencer — valve exhaust only |
6 mm OD: PPA6; 8 mm OD: PPA8; 10 mm OD: PPA10; 12 mm OD: PPA12 |
| US98A/UE95A PU tubing |
6 × 4 mm OD × ID: US98A060040100MBU,UE95A060040100MBU; 8 × 5 mm OD × ID: US98A080050100MBU,UE95A080050100MBU; 10 × 6.5 mm OD × ID: US98A100065100MBU,UE95A100065100MBU; 12 × 8 mm OD × ID: US98A120080100MBU,UE95A120080100MBU |
| ASC inline threaded flow control |
two female G3/8: ASC30010G |
| GAFR upstream filter/regulator |
female G3/8: GAFR30010SG,GAFR40010SG |
All listed parts are separately selected alternatives, not an included kit or stock promise. Use G3/8 cylinder fittings and the specified seal; PT, G and NPT are not interchangeable. Check insertion depth, tool/rotation clearance, flow and tube loading. G joints require the correct face seal and mating surface. The M20 × 1.5 rod thread is not an air port.
Use suitable soft nylon or PU tube. Match OD, and compression fittings also require the stated ID. D is black and blank is gray where offered; -M is miniature. -S specifies only the stainless 304 parts identified in the component material table, not the whole cylinder/circuit. GPHF has an additional female G3/8 branch: connect or seal it as the designed circuit permits; it is not another tube socket. Tees, Y, cross and distribution fittings must not bridge the two cylinder chambers or unrelated control circuits.
SE80 operates at 0.15–1 MPa and −20–70 °C. Ordinary push-in and listed flow controls are 0–1 MPa, −20–70 °C. GBPC is 0–0.9 MPa, 0–150 °C: the SE path is therefore no wider than 0.15–0.9 MPa and 0–70 °C. GBKC/GBB/GBD/GBZ is 0–1 MPa, 0–150 °C, limiting the SE path to 0.15–1 MPa and 0–70 °C. Every lower selected valve, tube and sensor limit still applies. Component vacuum ratings do not approve a vacuum SE assembly.
GBKC0806-03 accepts 8 × 5.5 or 8 × 6 mm tube; 8 × 5 mm tubing needs GBKC0805-03. Hold the body hex during thread installation, not the tube-locking nut; insert tube fully and tighten the nut. GBB/GBD requires the exact size and gender shown for the second end. BD/GBD ordering identifies the female size first and male size second. GBZ closes only a permitted unused auxiliary port, never either active cylinder working port.
At a cylinder port, A restricts cylinder/thread → tube exhaust (meter-out), with free reverse supply; B restricts tube → cylinder supply (meter-in). Use A for the usual double-acting exhaust-control circuit; choose B only for a designed meter-in circuit. Start closed and open slowly. Flow control is not safety isolation. GPTL 3/8 cap adjustment is recommended at 0.24 N·m, not pipe-thread installation torque. PSA/GPSA are threadless tube-to-tube controls without an A/B suffix; match both tube ODs and the body check/throttle symbol. The G in GPSA does not specify a G-thread port.
PPA6/PPA8/PPA10/PPA12 have 6/8/10/12 mm plain stems, requiring matching metric push-in sockets on the separately selected directional-valve exhaust. PPA uses POM body/cap and PE filter, rated 0–1 MPa and −20–70 °C; 25 dB at 0.5 MPa is a catalog test, not a site-noise promise. PPA has no D or thread suffix. PPA and threaded silencers must not occupy cylinder working ports or serve as inlet filters or safety shutoffs. Match actual exhaust thread/flow and check backpressure; GBESL adjustment changes backpressure.
ASC is a separate female-port inline control requiring its own fittings; follow P/A and the check/throttle symbol. Its 0.05–0.95 MPa component range limits the SE path to 0.15–0.95 MPa before other lower limits. Use 40 µm or finer filtered air.
GAFR300/400 S examples are separately connected upstream compressed-air filter/regulators: PC bowl, manual/differential-pressure drain, bracket, round clip-on gauge, 40 µm element and no reverse-flow valve. Inlet ≤1 MPa; setting 0.15–0.9 MPa; −5–70 °C, non-freezing. Check required flow, pressure drop, condensate and bowl environment; not a vacuum regulator, cylinder-mounted part or mandatory bore-specific size. Set pressure within every downstream rating.
US98A/UE95A examples are blue 100 m coils, not supplied cut lengths. Their 1 MPa rating is at 23 °C and requires temperature derating. US98A is −20–70 °C; UE95A is −40–70 °C, while the SE assembly stays within every component limit. Match OD and ID, bend radius, routing and actual flow. Only the stated selection-table tube sizes have the reference-speed association; other listed ODs do not inherit it.
