Specifications: MBL63X10SUSDB — AirTAC MBL aluminum alloy mini cylinder, double acting, single rod, 63 mm bore and 10 mm stroke. PT1/4 port; magnetic piston.
MAL to MBL Replacement
This listing is for MBL63X10SUSDB. The MAL series is discontinued. All orders placed under the corresponding legacy MAL listing MAL63X10SUSDB are fulfilled with MBL63X10SUSDB. The cylinder supplied will be MBL, not MAL. The bore, stroke, magnetic option, rear-cover code, mounting code and port-thread selection are retained in this ordering correspondence.
The supplied MAL catalog covers 20, 25, 32 and 40 mm bores; it does not document the old 63 mm MAL reference. The dimensions and specifications below belong to the documented MBL model. They do not verify the dimensions or direct interchangeability of an old MAL63X10SUSDB cylinder.
Mounting check: this retained order code combines U (flat rear cover) and SDB (rear pivot bracket). The catalog lists both choices but illustrates the SDB pin connection on the CA pivot eye. Do not assume that this flat U cover can connect directly to the bracket; check the supplied rear connection against the machine installation.
Product Catalog
Download AirTAC MBL / MBLC Catalog (English PDF)
Download AirTAC MAL Legacy Catalog (Chinese PDF)
Read the MAL vs MBL Dimensions and Replacement Guide
Download AirTAC 2022 Sensor and Mounting Compatibility Guide (PDF)
Download 2022 mounting brackets (PDF)
Download 2022 rod-end joints and sensor mounts (PDF)
Download 2022 cylinder installation and weight tables (PDF)
For detailed product dimensions and mounting drawings, please download and refer to the PDF catalog.
Model Code Explained
| Code |
Meaning |
| MBL |
aluminum alloy mini cylinder; double acting, single rod |
| 63 |
Cylinder bore: 63 mm |
| X10 |
Stroke: 10 mm |
| S |
Magnetic piston |
| U |
flat rear cover with radial air port |
| SDB |
rear pivot bracket |
| No thread suffix |
PT pipe thread (catalog default) |
Technical Specifications
| Parameter |
Details |
| Model |
MBL63X10SUSDB |
| Product type |
aluminum alloy mini cylinder |
| Operation |
double acting, single rod |
| Bore |
63 mm |
| Stroke |
10 mm |
| Piston-rod diameter |
16 mm |
| Rod-end thread |
M14 × 1.5 |
| Working medium |
Air filtered to 40 µm or finer |
| Operating pressure |
0.15–1.0 MPa |
| Proof pressure |
1.5 MPa |
| Operating temperature |
−20 to +70 °C |
| Piston speed |
30–800 mm/s |
| Port |
PT1/4 |
| Cushioning |
Bumper |
| Magnetic piston |
Included (S) |
| Stroke tolerance |
+1.0 / 0 mm up to 150 mm; +1.5 / 0 mm above 150 mm |
| Rear cover |
flat rear cover with radial air port |
| Mounting code in this model |
SDB — rear pivot bracket |
Features and Operation
- Alternating the supply and exhaust at the two cylinder ports drives extension and retraction.
- The tube and end-cover construction is not intended for dismantling. Protect the rod and sliding surfaces, and keep the load aligned with the cylinder axis.
The catalog describes a compact piston with a two-way sealing arrangement and a grease-retaining function. The aluminum-alloy tube and end covers use a rolled connection. The English overview contains a stainless-steel wording inconsistency; the material table and Chinese MBL chapter identify an aluminum-alloy tube.
External and Mounting Dimensions
The following symbols refer to the MBL drawing for 63 mm bore, 10 mm stroke and U rear cover in the 2022 cylinder catalog, printed page 114. Values are in mm unless a thread or formula is stated. The symbols retain the drawing references and must not be rearranged into an unsupported length × width × height.
| Parameter |
Details |
| A — base length before the stroke term |
146 mm |
| AB |
54 mm |
| AC |
92 mm |
| B — body dimension in the drawing |
68 mm |
| M — body mounting thread |
M36 × 2 |
| G |
46 mm |
| EA |
24 mm |
| Overall length from the printed formula |
156 mm |
| Drawing length relation |
A + stroke |
| AD |
22 mm |
| C |
20 mm; drawing tolerance ±0.07 mm |
| D |
16 mm |
| DA |
32 mm |
| MA |
22 mm |
| E |
M14 × 1.5 |
| EB |
22.5 mm |
| F |
19 mm |
| FA |
8 mm |
| GA |
11 mm |
| H |
14 mm |
| P |
PT1/4 |
| PA |
11 mm |
| AC + stroke |
92 + 10 = 102 mm |
| Magnetic versus nonmagnetic dimensions |
The catalog states that the external dimensions are the same. |
SDB mounting reference from printed page 116; use the dedicated bracket drawing to locate the symbols. The fixed bracket values below are distinct from stroke-dependent cylinder assembly dimensions.
| Parameter |
Details |
| D |
27 mm |
| Q |
20 mm |
| CA |
55 mm |
| CD |
56 mm |
| CF |
40 mm |
| CH |
40 mm |
| CT |
3 mm |
| CP |
7 mm |
For detailed product dimensions and mounting drawings, please download and refer to the PDF catalog.
Additional SDB drawing coordinates for F-MA40SDB; mm unless stated.
| Parameter |
Details |
| S |
15 mm |
| CE |
71 mm |
| CQ |
28 mm |
The accessory ordering table explicitly assigns F-MA40SDB to this bore. The fixed bracket dimensions are shared; the page does not print a separate installed CB + stroke dimension for this 50/63 mm body, so the bore-40 installed length is not substituted.
Compatible Accessories and Sensors
| Accessory code |
Purpose and compatibility |
| F-MA63LB |
F-MA63LB: foot bracket for MBL series, 63 mm bore. Optional; not implied by this model code. |
| F-MA50FA |
F-MA50FA: front flange for MBL series, 63 mm bore. Optional; not implied by this model code. |
| F-MA40SDB |
F-MA40SDB: rear pivot bracket listed for the MBL 63 mm bore family, supplied with its matching pin. The installation drawing uses a CA pivot-eye rear connection. This model has a flat U cover; direct pin mounting to that U cover is not shown. |
| F-MAC50I |
F-MAC50I: rod-end eye joint for MBL series, 63 mm bore. Optional; not implied by this model code. |
| F-MAC50Y |
F-MAC50Y: rod-end fork joint for MBL series, 63 mm bore. Optional; not implied by this model code. |
| F-M14X150F |
F-M14X150F: floating joint for MBL series, 63 mm bore. Optional; not implied by this model code. |
| F-M14X150U |
F-M14X150U: spherical rod-end joint for MBL series, 63 mm bore. Optional; not implied by this model code. |
For this magnetic MBL cylinder with 63 mm bore, the 2022 sensor selection table lists CMSG and DMSG with the round-cylinder mounting band F-MQA63. The band matches the aluminum cylinder body; do not substitute a tie-rod bracket or a different bore size. Sensors and bands are selected separately and are not implied by the S piston-magnet code.
Fit the sensor into the band holder, wrap and fasten the band around the cylinder, move it to the required detection position, then tighten the sensor and band fasteners. Select the complete sensor order code to match the required supply voltage, output circuit, wiring and cable length; CMSG/DMSG here identify compatible sensor profiles.
The 2022 Chinese MBL selection specifies CMSG/DMSG profiles and the bore-matched round-body band. The supplied English edition also lists EMSG; that additional edition entry does not change the Chinese CMSG/DMSG selection stated here. Select the complete electrical sensor code separately.
Weight Reference
1324 g — estimated configuration weight. The cylinder reference is 1131 g from the separately labelled MBL table for 63 mm bore, 10 mm stroke and U rear cover plus the printed 15 g magnetic-piston allowance (2022 Chinese catalog, printed page 426). The selected F-MA40SDB mounting accessory contributes an estimated 178 g from its low-carbon-steel plate dimensions. The mounted total is an estimate, not an AirTAC published assembly weight or a measured shipping weight. PT, G and NPT options have no separate weight allowance on that page. All catalog weights and estimates are for reference only; actual product weight prevails.
Force Reference
Calculated theoretical force at 0.5 MPa: extension 1557.8 N; retraction 1457.4 N, using bore 63 mm and rod diameter 16 mm. This pressure × effective-area calculation excludes friction, acceleration and safety/load factors; it is not a guaranteed usable load. Check the actual operating pressure and mechanism load.
Internal Components and Materials
| Component |
Catalog material |
| Piston rod |
S45C, hard-chromed and ground |
| Tube, covers and piston |
Aluminum alloy |
| Hexagon nut |
Carbon steel |
| Fasteners |
Alloy steel |
| O-rings |
NBR |
| Bumper / cushion ring |
TPU |
| Wear ring |
Wear-resistant material |
| Magnet |
Plastic magnet |
Numbered material reference from the MBLC-CA cutaway in the 2022 Chinese catalog, printed page 114. The shared body parts are identified below; this ordinary MBL model uses bumper cushioning, not the adjustable pneumatic cushion of MBLC. The piston magnet is present only in S models.
| Parameter |
Details |
| 1 — Rod hexagon nut |
Carbon steel |
| 2 — Piston rod |
S45C, hard-chromed and ground |
| 3 — Front-cover seal |
NBR |
| 4 — Front-cover nut |
Carbon steel |
| 5 — Front cover |
Aluminum alloy |
| 7 — Cylinder tube |
Aluminum alloy |
| 8 — O-ring |
NBR |
| 9 — Piston |
Aluminum alloy |
| 10 — Piston seal |
NBR |
| 11 — Magnet (magnetic version only) |
Plastic magnet |
| 12 — Wear ring |
Wear-resistant material |
| 13 — Screw |
Alloy steel |
| 14 — Rear cover |
Aluminum alloy |
Series Ordering Reference
Standard strokes listed for this bore and operating variant: 10, 15, 20, 25, 30, 40, 50, 60, 75, 80, 100, 125, 150, 160, 175, 200, 250, 300, 350, 400, 450, 500 mm. These are alternative order selections; they are not additional travel available from the current cylinder.
Select the operating variant, bore, stroke, magnetic option, rear-cover form, mounting accessory and pipe-thread option from the corresponding ordering chart. Do not transfer rear-cover or mount choices between single-rod, double-rod and adjustable-stroke versions without checking their dedicated row.
For the ordinary MBL series, the catalog lists a maximum standard stroke of 500 mm and an allowable special stroke of 800 mm. A special stroke requires its approved order and drawing; it is not extra travel available from the current cylinder. CA and U are the listed rear covers. CM is an old MAL rear-cover option and is not an MBL ordering code.
Selection, Installation and Use
- Select the bore and operating pressure from the required force, then check the stroke, moving load, speed, cushioning and mounting method for the mechanism.
- Flush the air lines before connection. Keep sealing tape or sealant clear of the first 1–2 thread turns and prevent water, particles or corrosive gases entering the cylinder.
- Keep the rod axis aligned with the load. Provide guides or supports where needed; avoid direct side loading and twisting of an unguided piston rod.
- Start speed adjustment with the flow-control valve closed and open it gradually. Meter-out control is the usual reference circuit; verify the actual single-acting or double-acting circuit.
- Factory-prelubricated cylinders can be used without additional lubrication. If a lubricator is used, the general instructions specify additive-free ISO VG32 turbine oil and continued lubrication.
- Isolate the air supply and exhaust residual pressure before servicing. Secure retained loads and prevent unexpected movement on restart. Protect against freezing, corrosion and strong external magnetic fields where magnetic sensing is used.
Circuit-selection reference at a theoretical 500 mm/s: for 63 mm bore the general catalog lists effective area 8.1 mm², valve examples 5V21008 / 5V22008, pneumatic-pilot alternatives 4A21008 / 4A22008, flow control PTL02, silencer BSL02, and tubing 10 mm OD × 6.5 mm ID. These are selection examples, not included components or a guaranteed installed speed; check actual port/thread adapters, pressure loss, tube length and load.